1. Introduction
A беседка is a popular outdoor structure. Many people choose алюминий for its light weight and strong resistance to rust. But a беседка needs a good drainage system. Without it, rain can cause big problems.
This article explains the European rules for беседка gutters. It gives clear facts about sizes, materials, and design. The information comes from official European standards (EN) and British standards (BS). We use short sentences and simple words. Our goal is to help you understand what matters most.
Key terms you will see often: беседка, алюминий, 6063-T5, 6063-T6, gutter, downpipe, and coating.
2. Why is the gutter so important?
We already know that water is heavy. One square metre of water with a depth of 1 cm weighs 10 kg. If a беседка roof holds 10 cm of water, that adds one tonne of extra weight. That can bend the frame or even break it.
A good gutter takes water away quickly. It protects the surface coating. It stops water from washing away the ground under the posts. It also keeps the sitting area dry and safe. In winter, it prevents dangerous ice falls.
So the gutter is not a small detail. It is a key part of the whole structure.
3. Main European standards for pergola gutters
Europe has many standards. They do not give one fixed size for every gutter. Instead, they give rules for performance, strength, and safety. Here are the most important ones.
3.1 EN 612:2005 – Metal gutters and downpipes
This standard covers gutter and downpipe products made from metal sheets, including алюминий. It tells manufacturers what materials to use. It also sets rules for dimensions, joints, and connections. If a беседка gutter meets this standard, you know it has passed basic quality tests.
3.2 EN 12056-3:2000 – Gravity drainage inside buildings
This is a very important standard. It gives the method for calculating how much water a gutter can carry. You must consider local rain intensity and roof area. The standard provides formulas for flow rate and required gutter size. Most products show their capacity based on this standard.
3.3 EN 1433:2002 – Drainage channels for people and vehicles
This standard applies to ground drains. If your беседка has a floor drain or a channel that people walk on, you need this standard. It defines load classes from A15 (light foot traffic) to F900 (heavy aircraft). For a home беседка, A15 or B125 is usually enough. But if cars drive over it, you need a higher class.
3.4 Other related standards
●EN 15088:2005 – covers алюминий structural products.
●BS EN 755-2 и BS EN 12020-2 – specify extruded алюминий profiles.
●BS EN 12206-1:2004 – for powder coatings on алюминий.
●EN 13501-1 – for fire classification. Most алюминий systems reach class A2 s1,d0, which means non combustible, low smoke, and no flaming drops.
●EN 1462 – for gutter brackets. They must meet Class H strength requirements.
●All these standards work together. They make sure the gutter system is safe, durable, and fit for purpose.
4. Common sizes – not fixed, but typical
There is no single “European size” for a беседка gutter. But the market offers several popular dimensions. The table below shows typical width × height/depth values.
| Part | Common size (mm) | Notes |
| Gutter (half-round) | 125 × 100 | Also called 5 inch |
| Gutter (half-round) | 150 × 100 | Also called 6 inch |
| Box gutter | 100 × 75 | Square shape |
| Box gutter | 80 × 70 | Used for smaller balconies |
| Box gutter | 140 wide × 60 high | For bigger rain loads |
| Floor drain channel | 32.5 × 17.7 | For deck areas |
| Floor drain channel | 40 × 60 | Another common type |
| Round downpipe | Diameter 63, 76, or 102 | Circular pipes |
| Square downpipe | 76 × 76 or 102 × 102 | Square pipes |
Standard lengths are usually 3 m or 6 m. You can also order custom lengths.
For a louvered беседка (with movable slats), the drainage is often built inside the posts. These systems often use a DN50 outlet. That means a 50 mm pipe connection.
Remember: these sizes are only starting points. The correct size depends on your local rainfall and roof area. You must calculate the needed capacity using EN 12056-3.
5. Material requirements
5.1 Alloy grades
Most manufacturers use 6063 T5 or 6063 T6 алюминий. Both are extrusion grades. They have good strength and corrosion resistance.
●6063-T5 – slightly lower strength but easier to shape. It is common for many profiles.
●6063-T6 – higher strength because of heat treatment. It is preferred for load bearing parts like main beams and heavy gutter sections.
●Some products use 6063 T4, but T5 and T6 are more typical in Europe.
●Always check the alloy grade on the product data sheet. It tells you the mechanical properties.
5.2 Wall thickness
The standard wall thickness for алюминий gutters is 2.0 mm. For extra strength, you can get 2.5 mm or 3.0 mm. Thicker walls resist denting and bending better. They also last longer in harsh weather.
5.3 Surface coating
Bare алюминий can oxidise. But the real protection comes from the paint or powder coating. The coating must meet BS EN 12206-1. A high quality coating carries the Qualicoat label. This is a European quality mark for architectural powder coatings.
Powder coating gives two benefits:
●It stops corrosion.
●It provides a beautiful finish in any RAL colour.
●Choose a coating that is at least 60 80 microns thick for outdoor use.
5.4 Fire performance
Алюминий does not burn. When coated with non combustible powder, the whole system achieves class A2-s1,d0 under EN 13501 1. This means:
● Very limited contribution to fire.
● Little smoke production.
● No flaming droplets that could spread fire.
This makes алюминий gutters safe for residential and public areas.
6. Design and installation rules
Having good materials is not enough. You must design the system correctly. Here are the key points.
6.1 Calculate the required capacity
This is step one. Use EN 12056 3. You need:
● The design rainfall intensity (litres per second per square metre). Your local weather office can give this data.
● The effective roof area that drains to one gutter.
●The slope of the gutter.
The standard gives a simple formula:
Q = A × r
where Q is flow rate, A is roof area, and r is rainfall intensity. Then you choose a gutter size that can handle Q plus a safety margin.
Never guess the size. A wrong size leads to overflow or structural stress.
6.2 Provide a slope
Water must flow by gravity. So the gutter must have a slope. The minimum slope is 1 % (1 cm fall per metre). A slope of 2 % is better for heavy rain. This ensures water moves fast and does not pool.
6.3 Use at least two downpipes
One downpipe is a weak point. If it gets blocked, the whole gutter fills and overflows. European practice requires at least two outlets for each gutter run. This gives redundancy. If one blocks, the other still works.
6.4 Include overflow protection
Even with two downpipes, leaves or debris can clog them. So you need an overflow device. This is usually a slot or a lower edge on the gutter that lets excess water spill out safely – away from the posts and people.
Overflow is not optional. It is a safety requirement in many countries.
6.5 Choose strong brackets
В gutter must be fixed securely. Brackets hold it to the беседка frame. They must comply with EN 1462 and meet Class H. Class H brackets are tested for high wind and snow loads. They do not loosen over time.
Space the brackets correctly – typically every 600 800 mm. Closer spacing gives more support.
6.6 Allow for thermal expansion
Алюминий expands and contracts with temperature changes. The coefficient is about 0.024 mm per metre per °C. For a 6 m length, a 50 °C change causes about 7 mm movement.
So you must leave expansion gaps. Use sliding connectors or flexible seals. A good rule is 1 mm per metre of length. This prevents buckling or pulling apart.
6.7 Ensure proper sealing at joints
Joints between gutter sections must be watertight. Use rubber gaskets or silicone sealants that are UV stable. Also use stainless steel screws and rivets – never mild steel, which rusts and stains.
7. Why choose aluminum over other materials?
Many people ask: why алюминий for a беседка gutter? Here are the advantages.
● Light weight – easy to handle and install. Less load on the roof frame.
● Corrosion resistance – no rust, even in coastal areas (if coated properly).
● Recyclable – good for the environment.
● Long life – with good coating, it can last 30+ years.
● Attractive finish – powder coating gives a smooth, modern look.
Compared to steel, алюминий does not need painting every few years. Compared to plastic, it is stronger and does not sag or crack in sunlight.
8. Practical tips for buyers and specifiers
If you are buying or designing a беседка with a gutter, follow these steps.
1.Get local rain data – ask your local authority or use online tools. Know the 5 minute peak intensity for your area.
2.Measure your roof area – calculate the horizontal projection of the roof. That is the area that collects rain.
3.Perform the calculation – use EN 12056 3 to find the minimum flow capacity. Add a 20 % safety margin.
4.Select a product with clear certification – look for EN 612 compliance and Qualicoat coating. Ask the supplier for test reports.
5.Check the alloy – prefer 6063 T6 for main structural parts. 6063 T5 is acceptable for non load profiles.
6.Inspect the brackets and seals – make sure they are stainless steel or anodised алюминий. Check that seals are UV resistant.
7.Plan the downpipe route – lead water away from the беседка base. Direct it to a drain or a soakaway.
8.Hire a professional installer – correct slope and sealing require skill. A bad installation ruins even the best materials.
9. Common mistakes to avoid
Many DIY projects fail because of these errors.
● No slope – water stays in the gutter and causes corrosion and weight.
● Only one downpipe – if it blocks, the roof floods.
● Wrong size – too small, and water overflows during every storm.
● Poor joints – leaks damage the coating and the frame.
● No expansion gap – the gutter buckles or pulls the brackets loose.
● Cheap brackets – they bend or break under snow or wind.
Avoid these mistakes, and your беседка will last for decades.
10. Summary and final advice
European standards do not give one fixed gutter size. They give a complete system of rules. The main idea is to design for your specific location and weather.
Remember these key points:
● Use EN 612 for product quality.
● Use EN 12056 3 for capacity calculation.
● Use 6063 T6 алюминий for strength and Qualicoat coating for protection.
● Provide slope, two downpipes, overflow, and expansion gaps.
● Select strong brackets to EN 1462 Class H.
A good gutter system is not expensive. But a bad one can destroy your беседка and cause accidents. So spend time on the design. Ask your supplier for clear data. Check the compliance marks.
With the right gutter, your беседка will stay dry, safe, and beautiful for many years. Rain will become a pleasure – not a problem.
11. About Alummira – a reliable supplier
Choosing the right gutter system is only half the work. You also need a supplier who can deliver quality products on time. Алуммира is one such company.
Алуммира specialises in custom алюминий profiles. They have 10 years of experience in алюминий extrusion. This means they know how to make strong, precise profiles for беседка systems. Their long history in production gives them deep knowledge of materials, dies, and manufacturing processes.
They also have 7 years of experience in international trade. This is important for buyers outside China. Exporting алюминий products involves many steps: packaging, shipping, customs clearance, and documentation. A supplier with trade experience handles these steps smoothly. This reduces delays and avoids costly mistakes.
For a беседка project, you may need custom gutter sizes or special profiles. Алуммира can help. Their production team works with alloys like 6063-T5 и 6063-T6. They understand the European standards we discussed earlier. They can produce profiles that meet EN 612 and other requirements.
Here are the key benefits of working with Алуммира:
● 10 years in extrusion – reliable production quality.
● 7 years in export – fast and accurate shipping.
● Custom profiles – made to your specific design.
● Knowledge of standards – they know EN and BS requirements.
If you are looking for a trusted partner for your беседка gutter project, you can contact them directly:
📧 Email: info@alummira.com
They can answer your questions about profiles, coatings, and delivery times. They can also provide samples and technical data sheets.